Skylight replacement Urbandale, flashed to stay dry

Skylight replacement Urbandale homeowners need starts with proper flashing, not just a hole in the deck. Failed units are replaced, leaking curbs are re-flashed, and new units are cut, framed, flashed, and sealed for snow loads and summer hail, whether during a roof replacement or as a retrofit into an existing roof.

Skylight replacement Urbandale: skylight with step flashing set into a shingle roof — photo 1 on this pageRoof and attic walkFlashing photosHose test
  • Roof walkedPitch and deck checked first
  • Flashing shownPhotos before shingles go down
  • Tested before closeoutWater run over the curb
  • Site cleanedNails magnet-swept from the yard

What skylight replacement covers

Every skylight scope includes the roof work, the unit, and the interior finish as one scope. A second unit, a vented operator, or drywall repair around an oversized opening is described separately in the written scope and shown up front.

Two-story gray home with charcoal shingle roof and attached two-car garage
  • Framing and deck cut

    The opening is cut, rafters are doubled, and headers are built to code. The cut is laid out from above and below so the unit lands square in the ceiling and true to the shingle course.

  • Curb and flashing system

    Curb construction, ice and water shield wrap, step flashing, and counter flashing are all included.

  • Skylight unit and glass

    The skylight itself, whether fixed, vented, or tubular, is part of the scope. The unit rating is matched to roof pitch and the glass spec is confirmed for hail and UV. No brand is named on this site.

  • Interior trim and seal

    Drywall returns, trim, insulation at the curb gap, and paint-ready finishing are included. The result is a finished opening inside, not a raw hole with plastic over it.

  • Ventilation check

    Attic intake and exhaust around the new opening are checked and adjusted if the skylight changes airflow. That keeps moisture from trapping at the curb and protects shingle life.

  • Cleanup and haul-off

    Shingle scraps, packaging, and old unit materials are hauled off. The interior is swept and the yard is magnet-swept for nails before leaving.

Homes and businesses.

The approach is the same for a home and a business. What changes is the access, the schedule, and who needs the paperwork.

For Homes

Skylights go into bedrooms, bathrooms, hallways, and great rooms. The attic and ceiling structure are checked before a unit is recommended.

  • Dark bathroom or hallway
  • Old skylight that leaks
  • Fogged or cracked glass

For Businesses

Curb-mounted skylights go onto flat and low-slope commercial roofs. Property managers get a written scope and photo documentation of the flashing.

  • Flat-roof daylighting
  • TPO and EPDM curbs
  • Hail-damaged units

Skylight replacement in Urbandale, done to the flashing

A plain-language look at what skylight replacement involves and when it is needed.

See how it works

Skylight replacement in Urbandale is the roof work of removing a failed unit, rebuilding or re-flashing the curb, and setting a new unit with ice and water shield and step flashing integrated so the roof sheds water around it instead of into it. The whole sequence is handled: layout, framing, curb construction, underlayment tie-in, flashing, and interior finish trim. A skylight is only as good as the flashing beneath it, and that is where most failed units that get replaced went wrong. New installation into a roof without an existing opening is also described on this page, as supporting scope.

Homes here deal with 36.5 inches of snow on average (1991–2020 normals, Des Moines airport; a 36.7-inch variant appears in some summaries), freeze-thaw cycles from December through March, and hail that dents shingles. That combination punishes a poorly sealed skylight. If a bedroom is dark or a bathroom fan is doing nothing for moisture, a first visit shows whether a fixed, vented, or tubular unit fits the roof pitch and ceiling structure. The ceiling leak post explains how a curb leak shows up inside, and the winter preparation post covers skylight curbs before freeze-up.

A skylight stays dry because of the flashing under it, not the sealant on top.

Roofer installing a continuous ridge vent along a roof peak
What it is
Replacing a failed unit, rebuilding the curb, and setting a flashed skylight unit.
When it is needed
When a room needs daylight, a bathroom stays damp, or an old skylight leaks or fogs.
What to expect
A roof and attic walk, a written scope, the install, and flashing photos.

What skylight replacement looks like

Five steps from the first roof walk to the final interior trim.

  1. Roof and attic walk

    The roof is walked and the attic is entered to check pitch, rafter spacing, deck condition, and existing ventilation. The recommendation covers unit size, placement, and whether a fixed or vented skylight makes sense.

    • Roof walk
    • Attic check
    • Unit sizing
    Roofer installing metal valley flashing where two shingled roof slopes meet
  2. Layout and framing

    The opening is chalk-lined from above and below so the skylight lands where it belongs inside the room, then the deck is cut and the opening is framed with doubled rafters. Headers and framing meet the residential code, and the cut stays square to the shingle course.

    • Chalk line
    • Deck cut
    • Rafter framing
    Roofer nailing starter-strip shingles along roof eaves with a nail gun
  3. Curb, flashing, and unit set

    The curb is built, wrapped in ice and water shield, and the unit is set, with step flashing layered into the shingles with a roofing nail gun. Flashing sits under the course above and over the course below, so water never finds an edge to work under.

    • Curb build
    • Flashing layers
    • Unit set
    Roofer installing hip cap shingles down the hip of a brown shingle roof
  4. Seal, trim, and vent check

    The curb gap is insulated, the interior is sealed with trim and drywall returns, and attic ventilation around the new opening is checked. If the unit is vented, the operator and screen are tested. The work area is swept and the shingles are hauled off.

    • Curb insulation
    • Interior trim
    • Vent check
    Roofer sweeping loose debris off a newly finished gray shingle roof
  5. Final inspection and walkthrough

    Photos of the flashing before the shingles went back down are shared, along with a moisture check, a hose test, and a walkthrough.

    • Moisture check
    • Hose test
    • Walkthrough
    Roofer on a roof receiving a shingle bundle from a coworker on a ladder

Tools and methods used on skylight work

Move across a circle, or focus it and press Enter, for an illustrative thermal view of the photograph.

  • Aerial view of a suburban street intersection and shingle rooftops in summer

    Roofing nail gun

    Fastens shingles and step flashing at the correct depth so the flashing sits flat and the shingle course above covers it cleanly.

  • Centered front view of a split-level stone home with tan shingle roof in snow

    Chalk line and utility knife

    Marks the opening from above and below so the cut is square to the shingle course and the unit lands true in the ceiling.

  • Extension ladder and safety harness at a roof eave — photo 13 on this page

    Pry bar and roofing hammer

    Lifts shingle courses around the curb without tearing them, and sets flashing edges tight against the curb.

  • Centered front view of a two-story home with brown shingle roof in autumn

    Moisture meter

    Checks the deck and curb for hidden moisture before and after the install so the opening is known dry.

  • Spring street view with flowering trees and shingle-roofed homes on both sides

    Safety harness and roofing ladder

    Keeps the crew tied off on steep pitches and gives safe access to the ridge and curb on two-story homes.

Thermal views are illustrative, generated from the photographs.

Methods

  • Air compressor

    Runs the nail gun and blows debris out of the curb and flashing channels before the unit is set.

  • Ice and water shield curb wrap

    The entire curb is wrapped in ice and water shield before the unit goes on, so any water that gets behind the flashing has nowhere to go but out.

  • Layered step flashing

    Each shingle course gets its own step flashing piece, layered under the course above and over the course below. This is the detail that addresses wind-driven rain and ice dam backup.

  • Flashing kits matched to the unit

    Flashing kits matched to the unit and roof pitch are used instead of site-bent metal alone. No brand is named on this site.

  • Hose testing before closeout

    On a dry day, water is run over the flashing and the interior is watched before the job is called done. If anything shows, it is fixed before the shingles are sealed.

Situations where skylight work is the scope

Weathered brown architectural asphalt shingles in staggered overlapping courses

Dark bathroom

A dark interior bathroom with no exterior wall for a window

A vented skylight sized to the ceiling bay is installed, framed and flashed, and the bath fan and attic ventilation are checked to work together. The vented unit pulls steam out.

Outcome: Daylight most of the day and a bathroom that dries out instead of staying damp.

Roofer smoothing dark ice-and-water shield membrane along roof eaves

During re-roof

A roof replacement already scheduled this season

The skylight is added to the roof replacement scope so the curb and flashing go in while the deck is open. No retrofit cut, no patching into new shingles.

Outcome: A cleaner flashing tie-in, with the curb and flashing installed as part of one open-deck sequence.

Roofer stripping old shingles with a long-handled tear-off shovel

Leaking old unit

A 1980s skylight that has leaked twice and fogs up

The old unit is pulled, the deck and framing are inspected, the curb is rebuilt with ice and water shield, and a new unit is set with a fresh flashing kit and interior trim.

Outcome: A dry ceiling, clear glass, and documented flashing photos for the file.

Gloved hands cutting an asphalt shingle with a hook-blade knife along a straightedge

Great room light

A great room or stairwell that feels closed in

Two or three fixed skylights are laid out in a row, each opening is framed, and they are flashed as a set so the roofline stays clean and the light spreads across the room.

Outcome: A brighter room without adding wall windows or changing the footprint.

Split-level home with stone chimney and gray shingle roof in autumn

Flat-roof office

A flat-roof addition over a home office

A code-height curb is built on the low-slope roof and flashed with membrane, then a fixed unit rated for flat-roof installation is set.

Outcome: Daylight in a room that had none, with membrane flashing that handles ponding.

Residential street in winter with light snow on shingle roofs and lawns
Waterford PointeTimberlineRolling Green

Skylight replacement Urbandale: how a project runs

Urbandale roofs take a specific beating: snow, freeze-thaw cycles from December through March, and hail. Skylight flashing here has to handle ice dam backup, not just rain. Many homes were built with original skylights whose seals have failed and whose flashing was never layered correctly.

When skylight work is planned with a roof replacement, the curb and flashing go into the tear-off sequence so the roof and unit go in as one system. The variables that shape a scope are attic access, roof pitch, and whether the ceiling needs drywall work.

  • Waterford Pointe: Two-story homes with steep pitches need harness work and careful ladder placement, and many have original skylights due for replacement.
  • Timberline: A mix of older ranches and newer builds, so both retrofit cuts and skylights added during roof replacements are seen.
  • Rolling Green: Bathroom skylights are common here, and bath fan and attic ventilation are checked together before a vented unit is recommended.
  • Northview Estates: Newer roofs with architectural shingles, where matching the shingle system around the opening keeps the repair invisible.
  • Waterford Glenn: Larger lots and mature trees mean debris piles on the uphill side of skylight curbs, so that area is cleared and inspected on every visit.
  • Ice dam backup at the curb: Meltwater refreezes at the roof edge and backs under flashing. The curb is wrapped in ice and water shield and step flashing is layered so water cannot work uphill.
See the area pages
  • The roof and attic are walked and options explained.
  • Drop cloths are laid and setup is done before cutting.
  • The flashing is tested and the unit walked through.

From problem to finished result.

Split-level home with brown shingle roof and terraced yard in autumn evening
IllustrativeThe thermal view is generated from the photograph. It is not a measurement. Drag the handle, or use the arrow keys once it is focused.
  • Leaking 1990s skylight replaced

    Before: A 1990s fixed skylight had leaked twice, staining the ceiling and softening the deck at the curb. The original flashing was a single bent piece with sealant over the top, and the sealant had cracked through years of freeze-thaw.

    After: The unit was pulled, soft deck was replaced, the curb was rebuilt with ice and water shield, and a new unit was set with a matched flashing kit. The ceiling was patched, and the flashing was photo-documented before closeout.

    Clear debris from the uphill side of the curb each fall and have the flashing checked regularly. Reseal only if the metal flashing shows movement.

  • Two fixed skylights added during re-roof

    Before: A dark living room had no wall space for windows. The roof was due for replacement, and daylight was wanted without changing the room layout.

    After: Two openings were framed during the tear-off, both curbs were flashed into the new shingle courses, and the interior trim was finished as part of the same scope. The room gets daylight across the full day.

    Wipe the interior glass twice a year and keep the flashing clear of debris. Have the units checked at the same time as a roof inspection.

  • Vented bathroom skylight

    Before: A windowless bathroom stayed damp even with the fan running. Condensation ran down the mirror and the ceiling showed early mold at the corners. The attic ventilation was undersized for the moisture load.

    After: A vented skylight sized to the ceiling bay was installed, the curb gap was air-sealed, and the attic intake and exhaust were balanced. The bathroom dries out after showers, and the fan runs less.

    Open the vented unit during and after showers in humid months and clean the screen each spring. Check the curb sealant before winter.

Skylight problems this page addresses

Most skylight calls start with a stain on the ceiling or a unit that fogs up. Here is what sits behind those symptoms and how it is handled.

  • Ceiling stainCeiling stain under an old skylightWater is already past the flashing and into the deck. Left alone, it rots framing and ruins drywall and insulation. The entry is traced with a moisture meter and hose test, then the flashing and curb detail that failed are rebuilt. If the deck is soft, that section is replaced before the new unit goes in.
  • Ice dam backupIce dams backing water under the curbFreeze-thaw cycles push meltwater uphill under poorly layered flashing, and the leak shows up in February when it is least wanted. The curb is wrapped in ice and water shield and step flashing is layered so water cannot work backward. Attic insulation and ventilation at the curb are also checked, since warm air leaks feed ice dams.
  • Fogged glassFogged or failed sealed glass unitA blown seal means the insulating gas is gone. The unit fogs, loses efficiency, and eventually drips condensation onto the sill. The glass unit or the whole skylight is replaced depending on age and frame condition. Replacement units fit the existing curb in most cases, so the roof work stays minimal.
  • Hail crackSkylight cracked by hailA cracked lens lets water straight in and can shatter under the next storm. The roof around it may also have hail damage. The opening is covered, the damage is documented with photos for your insurer, and the unit is replaced with a hail-rated glass spec. Surrounding shingles are inspected at the same time and any hail damage is included in the record. Check your policy, agent, or carrier for coverage questions; this is not insurance advice. The hail damage post describes what hail hits look like.
  • Interior condensationCondensation on the interior glassMoisture on the inside of the pane points to a ventilation or humidity problem, not a roof leak. Ignored, it stains trim and grows mold. Attic ventilation, bath fan operation, and the curb insulation gap are checked. Often the fix is air-sealing and balancing intake and exhaust, not replacing the skylight.

Why homeowners add skylights

Daylight in the room and a ceiling that stays dry.

  • Real daylight, not lamps

    A fixed skylight delivers daylight without giving up wall space. North-facing bedrooms and interior bathrooms get usable daylight most of the day, which makes small rooms feel larger.

  • Moisture control in bathrooms

    Vented skylights open with a pole or remote and pull steam out of a bathroom faster than a ceiling fan. The unit is sized and attic ventilation is checked so the moisture leaves the house instead of condensing on the roof deck.

  • Flashing that handles Iowa snow

    Every skylight install gets ice and water shield wrapped around the curb and step flashing layered into the shingle courses. That detail is what addresses ice dams backing water under the unit in February.

  • Daylight without wall windows

    Dark hallways and windowless bathrooms get light without cutting a new wall opening or changing the footprint.

Records that go with the job

Clear records to keep and share.

Photo report

Flashing documented before shingles go down

Written scope

Unit, framing, flashing, and trim listed

Care sheet

How to operate and clean the unit

Fixed, vented, or tubular skylights

The unit type decides how much light the room gets and whether the room can vent moisture.

Vented

Opens with a pole or remote

  • Pulls steam from baths
  • Needs screen cleaning
  • Operator can fail

Tubular

Rigid tube to a ceiling diffuser

  • Fits tight attic spaces
  • Less direct light
  • Good for closets

What is worked with

  • Fixed units
  • Ice and water shield
  • Step flashing
  • Asphalt shingles
  • TPO membrane
  • EPDM membrane
  • Roof underlayment
  • Curb sealant

ZIP codes do not set the city line.

A mailing address can carry a neighboring city's name, and an Urbandale address can carry a neighboring ZIP code. A parcel record settles which city governs an address. Call and ask about a specific street.

  • Parcel record
  • City boundary
  • Call and ask

Roofing information by area.

The pages below hold roofing information for Urbandale plats and districts. Each page describes its area. Call and ask about a specific street.

View all area pages

Skylight questions heard on calls

This business publishes no prices on this site. A scope depends on attic access, roof pitch, curb condition, and whether the ceiling needs drywall work. The unit, framing, flashing, and trim are listed in the written scope before anything is cut.

A skylight leaks when the flashing is wrong, not because skylights are leak-prone. Ice dams and freeze-thaw cycles expose bad flashing fast. The curb is wrapped in ice and water shield, step flashing is layered into every shingle course, and the detail is hose-tested before closeout.

Fixed, vented, and tubular units each suit different rooms and roof pitches. Fixed units suit rooms that need light only; vented units suit bathrooms that need moisture out; tubular units suit tight attic spaces. The unit is matched to roof pitch and ceiling structure, and no brand is named on this site.

Yes. Replacement work is most of what this page describes: the opening is worked from above and below, the curb is rebuilt or re-flashed, and new flashing is tied into the existing shingle courses. If the shingles around the opening are near the end of their life, that is shown first so the choice is informed.

Skylight replacement in Urbandale — call to arrange a roof walk

Call Rocc Solid Construction at (641) 219-5108 to arrange a roof walk, an attic check, and a written scope before anything gets cut. The listed hours are Open 24 hours, every day.

Contact Rocc Solid Construction

Call (641) 219-5108 to talk about a roofing question. The office is at 3815 109th St, Urbandale, IA 50322, United States, and the listed hours are Open 24 hours, every day.